Fortsätt till huvudinnehåll

Visiting Itaipu


Itaipu dam has the second largest rated capacity of all hydropower plants in the world, next after Three Gorges Dam in China. However, as the Paraná river has a more even flow throughout the year, the Itaipu dam in the end is the hydropower plant in the world that supplies the most energy.
A normal year, this plant alone supplies more than 150% of the nuclear plants in Sweden together.

The dam was built and is operated within a binational co-operation between Paraguay and Brazil, that then divide the energy in between them, The ground where it stands has a somewhat international status.

Traveling in Brazil, I off course had to see this dam with my own eyes. Let's see some pictures I took. 

I photographed this overview picture of the dam for a start. 

The dam seen from the side. It doesn't look to vast here, but it's 7235 meters long in total. The turbines outlets are underneath the water surface and cannot be seen here.

 This is the outlet of cooling water from the generators. The cooling water leaves the generator at around 80°C before it's mixed with cool drainage water and is dispersed into the Paraná river.

   
These are channels for draining the dam, when there is a greater flow of water than the installed equipment can handle. 




The area that is flooded by the dam. As of what Itaipu claims it has one of the smaller flooded area per generated unit of energy  in the world though.

 The white towers sticking up are hydraulic pistons for operating shutter valves to the penstocks.

Another overview.

 Photo taken standing on the top of the dam. It's huge!

 Downstreams of the powerplant.


The  white penstocks for the turbines were just massive.

Penstocks again. 


Control room for the transformer stations. The policy is to have one operator from Paraguay and one from Brazil all the time.  The operation of the dam is complicated a bit as it supplies both Paraguay and Brazil, and these countries have different main frequencies on the power grid.




The control room for the turbines. As in many other places, it's a hybrid between old analogue supervising and a newer digital system. 


 A plate giving cred to the people who built the dam.


 The shaft transferring the mechanical power from one of the turbines to a generator. The shaft and the turbine is rotating at the rather modest speed of 90 RPM on the Brazilian side with the 60 Hz system. This should mean that the generator has 80 poles, am I right?


Underneath these circular areas in the floor the generators are located.




Kommentarer

Populära inlägg i den här bloggen

[VAWT] Plausible improvements of the Savonius windmill

Cut a barrel in half, mount it on a shaft and you have a windturbine. If the barrel is used, then what else probably would end up on a scrap heap is instead used for converting renewable energy. Simplicity and low cost makes this an attractive option especially for societies with limited economy and a malfunctioning or non existing electric grid. Small off-grid electrical networks can be built and people who perhaps most needs electricity get that. Isn't that neat? Savonius (from http://solarvan.co.uk/savonius) An overlooked potential? The Savonius though has a widespread reputation of having low effiency and is often dismissed as a credible option around forums and in formal litterature. However, when looking at the graph below from a publication Wortman did 1983, the effiency can be realtively high provided that the TSR(Tip-to-Wind-Speed-Ratio) is held at a correct value and the windmill should work quite nicely. In practice this could probably be done by controlling t

The heating system

One of my former projects was the design and practical realization of an automated wood fired heating system. Two key characteristics of the project were the reuse of junkyard bargains and realization of electronic system starting from component level. Budget was kept low. The system is now warming a house situated on a farm on the Swedish countryside.  I for sure have never done a project spanning so many different categories of work. In the end I had done manual metal work and welding, plumbing, electrical installation, creation of control- and calculation algorithms, circuit design and programming to name some. A box on the upper floor of the house with an Atmega328 microprocessor controls the whole heating  system.   Here is a video summary of the project: Systems furnace is a Braland 21 from http://www.braland.se The control system that is now up and running can among other things monitor 16 different temperatures, control all the systems pumps and do diffe

[VAWT] Affordable wind measurements

The shop Clas Ohlsson in Sweden sells a spare anemometer for the   WH-1080 weather station  for a hobbyist friendly price around 15 euros. This anemometer can probably be found in other countries too. The WH-1080 spare anemometer Here   you can read about how to use this anemometer together with an Arduino or any other embedded system.  As we couldn't find any data on the characteristics of this sensor, we did our own calibration in a wind tunnel and the results are presented in the report above. This anemometer was used in a Bachelors Thesis project related to the devlopment of optimization of the Savonius Turbine, here tagged [VAWT].